ReadyMadeRC
AIR TITAN KIT (HARDWARE INCLUDED) WITH MOTOR, ESC, AND SERVOS
| ATTENTION | According to |
| Wingspan | 2520MM/ 99.2inch |
| Kits Airplane weight | 2.4kg(5.3IB) including all reinforcement parts |
| Extra Payload | 3.0kg-4.0kg (6.6IB-8.8IB)/ flight weight>6.0kg |
| Customized Motor for Airtitan | M60K/ Power 1500W |
| Testing static thrust | 5.5-6.0kg (6S, 15" Prop) |
| Propeller recommend | 15*6 / 15*7 |
| ESC | Advanced 80A OPTO (without Built-in BEC) |
| External UBEC | 5V/6A,5.5V/6A or 6V/6A (Switchable) |
| Material of fuselage and Wing | EPO |
| RMRC 6s batteries found here | 10,000 mAh |
| Main-wing | built- in 4PCS alloy aluminum plus 2PCS carbon tube through the Main-wing |
| Control surface of Aileron and Elevator | carbon tube reinforced, no need further DIY |
Breakdown for Transport:, This plane carries over the “gentle stall” characteristics of the Penguin, but super sized. No scary tip-stalls. Instead, it has super predictable flight characteristics. Tricycle landing gear with a steerable nose gear is included, along with a stable high wing design, plus a bottom camera port, and secondary top camera mounting area. The ARF version includes an 80A OPTO ESC, Massive 1500W motor, a switch mode 5-6V adjustable UBEC, and heavy duty metal geared servos for the ailerons, elevator, and steering. Hand launch is possible, but you might need to work out a bit before you try it (see beginning of video!). Like the Penguin, this airframe was designed with FPV in mind, but would also serve as a great plane to fly at the field if you just want something you can strap a GoPro to, or maybe even 10 of them since it won’t mind the weight. Available and ready to ship now at Ready Made RC, LLC, the best place to get ALL your FPV and RC equipment!, Specifications:, , Customized Brushless Power system:, Servos:, , Battery Recommendations:, , Sample Battery Setup:, , Flight Recomendations:, *Note : 5S with a 15*8 Prop is okay if your flight weight is less than 5.5kg. A 6S pack will however provide “better power", *Note: Flight weight of 5.5kg-6.0kg can meet most FPV requirements, and we recommend less than 6.0kg for most FPV pilots, High Quality Reinforcement :, ,
UN1133 shipping regulations, the glue contained in t his product ...ReadyMadeRC
3DR PIXHAWK
| Weight | 38g (1.31oz) |
| Width | 50mm (1.96") |
| Thickness | 15.5mm (.613") |
| Length | 81.5mm (3.21") |
Note:, Pixhawk is a PPM-input autopilot, which means that it gets RC input from a single cable to the receiver, either via the PPM port, the Futaba S.BUS port, or the special satellite receiver port for Spektrum gear. Most modern RC receivers (and all those sold by 3D Robotics) allow for PPM output, but some, such as non-S.BUS Futaba receivers, do not. If your receiver does not support PPM output, please add a PPM encoder board option to your order below., Pixhawk includes:, , Options:, , Microprocessor:, , Sensors:, , Interfaces:, , Power System:, , Weight and Dimensions:, ,
Pixhawk is an advanced autopilot system designed by the PX4 ...ReadyMadeRC
SMARTFPV - GOPRO LIVE VIDEO CHARGE BOARD (STRAIGHT)
It plugs in to GoPro 30pin bus connector on back of camera and gives ability to get live video, charge camera and record HD video at same time. Board has 3pin Molex connector. Supplied 30cm cable will connect to Molex connector and provide you with Immersion RC/Fat Shark style connectors with convenient pin functions:, Black, Camera compatibility:,
This board is designed for GoPro HD HERO, HERO2 and ...ReadyMadeRC
PICO FPV COMBO (5.8 GHZ)
Package Includes:, , Camera Choices:, RMRC Pico V2 Camera (, Antenna Choices:, TrueRC Nano 5.8 RHCP Antenna, Altitude RC 5.8 Transmitter and optional True RC 5.8 Nano Antenna:,
This is a customizable combo for those looking for high ...ReadyMadeRC
PHOENIX R/C PRO SIMULATOR V5.0
| Spektrum DX4e/DX6/DX6i/DX7/DX7s/DX8/DX10T/DX18 (No adapter required) - Note | The DX7se is not compatible with the simulator. |
Features:, , Overview:, Whenever weather, schedules or circumstances conspire to keep you from the flying field, scratch your flying itch with the latest Phoenix Professional RC Flight Simulator, version 5.0. Stunning graphics and incredibly realistic physics have made the Phoenix simulator not only one of the best desktop flight simulators, but a virtual RC experience with just about all the benefits of an RC club and flying field. This newest version features definitively refined physics plus new companion software you can use to create your own models, fly them and then share them online. It’s always a perfect time to fly with the Phoenix Professional RC Flight Simulator., Tech Notes:, To successfully use Phoenix, you will need the following:, • IBM-compatible PC computer with 1.0 GHz Pentium 3/4 or AMD Athlon/64 compatible processor or better, Or alternatively:, • An Intel-based Apple Macintosh computer running Microsoft Windows XP, Vista or 7 with the above specifications under one of the following systems:, • Boot Camp (recommended), Adapter Requirements:, Adapters may be required depending on the transmitter you wish to use., supported:,
Improved airplane physics rebuilt from the ground up, plus industry-leading ...ReadyMadeRC
RMRC-520 520 LINE CCD CAMERA (NTSC)
| PAL | (H)752x(V)582; NTSC |
| PAL | 1/50~1/100,000 Sec; NTSC |
For users of UHF RC systems: It has been reported that this camera may emit noise in the 433MHz range, possibly reducing the range of your LRS system. If you are using one of these system, I recommend using one of my other cameras which have all been reported to work with no interference. I have not had any other reports of interference with other devices such as GPS receivers or other RC receivers.,
Mini high resolution camera 1/3 Sony super HAD CCD 520TV ...ReadyMadeRC
RMRC-520 520 LINE CCD CAMERA (PAL)
| PAL | (H)752x(V)582; NTSC |
| PAL | 1/50~1/100,000 Sec; NTSC |
Also Includes:, , For users of UHF RC systems: It has been reported that this camera may emit noise in the 433MHz range, possibly reducing the range of your LRS system. If you are using one of these system, I recommend using one of my other cameras which have all been reported to work with no interference. I have not had any other reports of interference with other devices such as GPS receivers or other RC receivers.,
Mini high resolution camera 1/3 Sony super HAD CCD 520TV ...ReadyMadeRC
CUSTOM 0.9 FPV STARTER PACKAGE: 900MHZ
| Instructions | HERE |
Package Stats with the following components:, , NOTE: if you purchase the "no camera" option, the transmitter will only come with the "stock" cable and does not include the custom ReadyMadeRC cable used for attaching it to the rest of the Ready Made RC cables or transmitter battery., Notice: The use and operation of this product in the USA and other countries may require an amateur/ham radio license, and some countries may forbid its use entirely. It is the responsibility of the purchaser to ensure that the use of this product meets the requirements imposed by your government’s rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. ReadyMadeRC cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations. Frequencies not allowed in the US will be disabled for those items shipped to US addresses.,
Eagle Tree OSD Pro-Ready...see option below! Built off of the ...ReadyMadeRC
ZEPHYR 2 ZII KIT
| http | //fpvlab.com/forums/showthread.php?1966-New-molded-Ritewing-Zephyr-II |
| http | //www.rcgroups.com/forums/showthread.php?t=1525711 |
Description from Ritewing RC:, The new injection molded EPOR Z II is finally here ,after 2 1/2 years of tweaking this beast she is finally making an apearance.She has the wing area of the older Z 60 in a 54 WS ,770 SQ inches of wing area makes her a monster little wing. She now will launch and land much easier than the past versions., This package includes:, Molded wings with equipment bays already included.,
Basic build manual located HERE . Review on Model Airplane ...ReadyMadeRC
ZEPHYR XL (ZXL) KIT
| http | //www.youtube.com/watch? |
| http | //www.youtube.com/watch? |
| http | //www.youtube.com/watch? |
| http | //fpvlab.com/forums/showthread.php?1966-New-molded-Ritewing-Zephyr-II |
| http | //www.rcgroups.com/forums/showthread.php?t=1525711 |
The original ZII description is below. We'll try to modify the specifics as we get them:, Description from Ritewing RC:, The new injection molded EPOR Z II is finally here ,after 2 1/2 years of tweaking this beast she is finally making an apearance.She has the wing area of the older Z 60 in a 54 WS ,770 SQ inches of wing area makes her a monster little wing. She now will launch and land much easier than the past versions., This package includes:, Molded wings with equipment bays already included.,
This is the new ZXL 81" monster! It starts with ...ReadyMadeRC
LAYERLENS FOR GOPRO HERO3 (V2)
For this reason, FPV Manuals developed LayerLens. LayerLens brings the most important part of the original GoPro case back: the protective lens; without adding much weight or size. Fully assembled, LayerLens for the GoPro 3 weighs only 7.5g — a small fraction the weight of the full GoPro case. LayerLens has become the standard lens protection product in the fields of RC and FPV where a GoPro is used outside of its standard housing.,
Details This is the new revision of LayerLens for the ...ReadyMadeRC
CASTLE CREATIONS PHOENIX EDGE 75 BRUSHLESS ESC, 34V MAX. W/BEC
| MIN | 2S LiPo MAX |
Helis:, 500 class, Fixed wing:, .40 - .52, Input voltage:, Max continuous amperage at full throttle:, 75 amps*, BEC voltage (voltage regulator for powering radio and sevos):, User selectable choice from 5 to 8.4 volt output, BEC output amperage:, 5 amp peak**, Width:, 2.0" (50.8mm), Length:, 2.8" (71.9mm), Height:, 0.9" (23.2mm), Weight w/wires:, 4.0 oz (113.4g), Weight w/o wires:, 2.5 oz (70.9g), Programmability:, Fully programmable Castle feature set using Castle Link USB adapter (coupon for free Castle Link USB adapter included in package) and freely downloadable Castle Link Windows software., Connectors:, Battery and motor connectors sold separately, Tools needed for installation:, Soldering iron and solder to attach bullets to motor wires and battery connector to power wires., *RC HOBBY APPLICATION RATING: 75 amps for the duration of a single 5,000 mAh battery pack with the ESC in contact with a 5 mph airflow of 25C (77F) or cooler air. Controller temperature must never exceed 100C (212F). Exceeding current or temperature ratings may damage components and may shorten the life of the ESC. Always verify system current draw at full-throttle. Decrease load or increase airflow to decrease the ESC’s operating temperature.,
With the debut of the Phoenix Edge series of ESCs ...ReadyMadeRC
TAROT 2 AXIS CAMERA GIMBAL FOR GOPRO HERO3, 3+ W/FREE CABLE
| 7. Supported receiver type | conventional/S-BUS/DSM2/DSMJ/DSMX receiver. |
| 8. Supported RC | PPM/PCM/2.4G. |
| 9. Operating supply | DC 7.4V~14.8V (Li-Po 3S is recommended) |
| 10. Operating current | 200mA-500mA (Depending on power supply voltage and motor power) |
| 11. Operating temperature | -15ºC~65ºC. |
| 12. CPU | Double 32bit ARM |
| 13. Sensor technology | 3-axis MEMS gyro and accelerometer. |
| 14. Max angular rate | 2000 º /sec. |
| 15. Max acceleration | 16g. |
| 16. Control frequency | 2000Hz |
| 17. Motor driver frequency | 20KHz (quiet and smooth) |
| 18. Control accuracy | 0.1° |
| 19. Control range | -45º~45º(roll), -135 º~90 º(tilt). |
| 20. Attitude arithmetic | BLDC gimbal dedicated brushless motor decoupled EKF algorithm. |
| 21. Aerial photography equipment | GOPRO Hero3. |
Note:, Modifications may be required to use HERO4, Parts included for the kit: 2 motors mounted onto the swing arms, gimbal controller board, mounting bracket with GoPro brace, 2 male to male servo cables (one with Y end), USB firmware updater connector and cable, 4 rubber dampeners and mounting bracket + hardware for the gimbal.,
FREE LIVE VIDEO OUT CABLE OPTION...YES, OUR CABLES WILL WORK ...ReadyMadeRC
RMRC PARALLEL CHARGING BOARD - 35A XT-60
| Housing Material | ABS Fireproof Material |
| Balance Tap | JST-XH |
| Cell Count | 2-6s |
| Fuse | 40A (4 fuses) |
| Size | 152x76x17.5mm |
| Maximum continuous current | 25A |
| Maximum current for short term | 35A (10 Minutes Max) |
Features:, , Specifications:, , NOTE:, Please follow all precautions included in manual before using this board for parallel charging. Not following these directions may result in fire and damages. Ready Made RC, LLC is not responsible for damaged batteries or property.,
Introducing the ReadyMadeRC Parallel Charging Board! The RMRC ParaBoard is ...ReadyMadeRC
RMRC PARALLEL CHARGING BOARD - 35A T-PLUG
| Housing Material | ABS Fireproof Material |
| Balance Tap | JST-XH |
| Cell Count | 2-6s |
| Fuse | 40A (4 fuses) |
| Size | 152x76x17.5mm |
| Maximum continuous current | 25A |
| Maximum current for short term | 35A (10 Minutes Max) |
Features:, , Specifications:, , NOTE:, Please follow all precautions included in manual before using this board for parallel charging. Not following these directions may result in fire and damages. Ready Made RC, LLC is not responsible for damaged batteries or property.,
Introducing the ReadyMadeRC Parallel Charging Board! The RMRC ParaBoard is ...